Chimney Repair in Hillsboro, OR | Chimney Sweep Hillsboro

Chimney Repair in Hillsboro - Camera Evidence Before Any Quote

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Hillsboro Homeowners

Chimney Repair in Hillsboro is for the homeowner who has a real symptom to deal with: a draft that won’t quit, a stain on the ceiling near the flue, loose bricks above the roofline, or a cap that went missing after a windstorm off the Coast Range. You don’t need a generalist who squeezes chimneys in between deck jobs. You need someone whose whole trade is this one system. Our technicians have up to 11 years of experience working exclusively on chimney sweeping, inspection, and repair, and we handle all three under one roof so nothing gets handed off to a third party. We answer the phone around the clock, and repair calls in Hillsboro get booked fast. Call (855) 473-8720 to get started.

Call (855) 473-8720

Chimney Cap Installation

Chimney Cap Installation is the first defense against everything the sky drops on your flue, and in the Willamette Valley that means rain, fir needles, and the occasional squirrel looking for a warm spot. A cap is the mesh-and-plate assembly that sits on top of the crown, letting smoke out while keeping water and wildlife from getting in. We install caps from Gelco, Famco, and Copperfield, sized to your actual flue rather than whatever a hardware store happens to stock. Typical cost runs $250 – $650 installed, depending on flue size and whether we’re working with one flue or several. You need one if your chimney is open at the top, which is more common than people expect.

What a Cap Actually Does

A cap keeps water out of the flue, blocks birds and squirrels from nesting, and stops sparks from landing on your roof. It also reduces the downdrafts that push smoke back into a room on gusty days. It’s a small piece of hardware with a big effect on how the whole chimney behaves.

Choosing the Right Size and Style

Caps are not universal. A single-flue wood chimney takes a different cap than a multi-flue masonry stack, and gas appliances need a cap with enough venting to draft correctly. Getting the sizing wrong causes more problems than it solves, so we measure before we order.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is the job when the cap you have has rusted through, lost its mesh, or blown loose in a storm. Caps take a beating from rain and temperature swings, and most fail from the fasteners first; the plate dries out, the screws pull, and next thing you know the whole assembly is hanging by one corner. We pull the old cap, inspect the flue and crown while we’re up there, and set a new one from Olympia Chimney or Gelco. Expect $275 – $700 for replacement, based on access and flue configuration. It’s worth fixing quickly, since a missing cap is an open invitation for water damage.

Spotting a Failed Cap

Look for rust streaks on the masonry just below the cap, mesh that sags or is missing, or a cap sitting visibly crooked. Any of those means it’s time to replace rather than patch. Water getting past a bad cap usually shows up inside the house before it’s obvious from the ground.

Matching the Replacement to the Flue

A replacement cap has to fit the flue it covers, and multi-flue stacks often need a full-width cover rather than individual caps. We take measurements and match the style to how your appliances vent. That way the new cap drafts properly and doesn’t create its own problems.

Chimney Liner Installation

Chimney Liner Installation is the structural heart of the system: the liner is the flue surface that carries smoke and gases up and out, and when it’s cracked or missing, the chimney isn’t safe to use. We install DuraFlex flexible liner systems for new installs and for replacing failed clay tiles, and our technicians work with DuraFlex on a regular basis, so the fit and the connections are right the first time. A full liner install typically runs $2,400 – $5,200 depending on chimney height, flue size, and whether we’re adding insulation around the liner. If your flue is damaged but structurally sound, HeatShield resurfacing may be the better option.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (855) 473-8720

When a Liner Needs Replacing

Cracked tiles, gaps between sections, a liner that’s separated from the chimney walls, or an appliance that’s been changed to a different fuel type all point toward replacement. A camera inspection shows the condition clearly. We won’t recommend a liner on a hunch.

HeatShield as an Alternative

HeatShield resurfacing repairs damaged flue tiles from the inside, restoring a smooth, sealed surface without pulling the whole chimney apart. It works when the flue is sound but the tile faces are worn or cracked. We’re trained to apply it and will tell you honestly whether it fits your chimney or whether you need the full liner.

Chimney Flashing Repair

Chimney Flashing Repair deals with the metal and sealant at the roof line where the chimney meets the shingles, and it’s one of the most overlooked sources of roof leaks. When flashing pulls away or the sealant breaks down, water runs down the side of the chimney and into the structure, often showing up as a ceiling stain far from the chimney itself. We reset and replace flashing, rework the step and counter-flashing, and seal the joints correctly. Flashing repair usually runs $350 – $900 depending on roof pitch and how much of the flashing needs rebuilding. It’s a set-per-job price confirmed in a written estimate before we start.

Reading the Signs of Flashing Failure

Staining on the ceiling or the chimney chase, rust on the flashing metal, or shingles lifting around the chimney base all point to a problem. Interior water stains that show up during and after rain are the clearest signal. Don’t assume the roof is at fault; the flashing is the more common culprit.

Why Flashing Failures Keep Coming Back

Most repeat leaks come from flashing that was patched rather than rebuilt. Tar or sealant over a failed joint buys a season. Correct flashing is layered into the shingles, and doing it properly means the repair actually holds through Willamette Valley rain.

Chimney Crown Repair

Chimney Crown Repair addresses the concrete or masonry slab on top of the chimney that sheds water away from the flue. When a crown cracks, water gets into the masonry below, freezes, and spalls the brick face; over a few seasons that small crack becomes structural damage. We rebuild crowns with a proper slope and overhang so water leaves the chimney instead of sitting on it, and we seal the flue joint while we’re there. Crown repair typically runs $450 – $1,200 based on the size of the crown and how much masonry has to be replaced. It’s a modest repair that prevents an expensive one.

What a Crown Failure Looks Like

Cracks wide enough to catch a fingernail, crumbling concrete on top of the stack, or moss growing on the crown all mean moisture is getting in. Spalling brick just below the crown is another sign. The fix is straightforward when it’s caught early.

Rebuilding for Proper Drainage

A crown needs a slope so water runs off, and an overhang so it drips clear of the masonry instead of running down it. New crowns are built to shed water correctly rather than sit flat. That detail is the difference between a wash job and a repair that lasts.

Want to talk it through?Free estimate, price agreed before work starts
Call (855) 473-8720

Chimney Repair Companies

Chimney Repair Companies in the Hillsboro area range from sweep-only outfits that hand off repair work to general contractors who do chimneys on the side, and picking the right one matters more than price alone. You want a company that inspects, sweeps, and repairs in-house so nobody is guessing about what another crew found. We do all three, our technicians have up to 11 years of chimney-specific experience, and we install professional materials from DuraFlex, HeatShield, Gelco, and Famco. A typical repair call runs $185 – $450 for smaller fixes, with larger projects quoted per job. The written estimate sets the final price, and the estimate is free.

Questions Worth Asking Before You Hire

Ask whether repair work is done in-house or subcontracted, what brands of liner and cap they install, and whether they’ll show you photos of what they found. A company that can’t answer these clearly is worth setting aside. A specialist will welcome the questions.

Why Specialists Beat Generalists Here

Chimneys are a narrow system with specific failure modes, and a general contractor who sees a handful a year will miss things a specialist catches immediately. The skill set builds only from repetition. That focus is why we carry the professional materials rather than what’s on the shelf at the hardware store.

Chimney Masonry Repair

Chimney Masonry Repair covers the brick and mortar itself: repointing joints, replacing spalled brick, and rebuilding sections of the stack that have absorbed too much water. Hillsboro chimneys sit through wet winters and dry summers, and that cycle is hard on masonry; freeze-thaw action widens cracks and pops the faces off brick. We repoint with the right mortar mix for older soft brick, replace damaged units, and rebuild where the damage runs deeper. Masonry repair typically runs $500 – $2,800 depending on the extent of the work. We’ll tell you plainly when a repair can safely wait.

Repointing Versus Rebuilding

Repointing grinds out the old mortar and replaces it without disturbing the brick, which is right when the units are sound but the joints are eroded. Rebuilding goes further and replaces the damaged section entirely. The camera and a close look tell us which one applies.

Matching Mortar to the Brick

Older brick needs a softer mortar that lets the masonry expand and contract; a modern hard mortar seals tightly and forces the brick to crack instead. Matching the mix to the chimney is the detail most contractors miss. Get it right and the repair lasts.

Brands We Service

We work with DuraFlex flexible liner systems for new installs and replacements, and our technicians know where they wear, where they seal, and how to get the connection at the top plate right. HeatShield is the other brand we use daily; it’s the resurfacing product that can save you the cost of a full reline when the flue is sound but the tile faces are worn. We’re trained to apply it, and we service chimneys that already have HeatShield work done.

Caps, covers, and components come from Gelco, Famco, Olympia Chimney, and Copperfield, depending on the fit and venting your chimney needs. Those are professional supply lines, not retail stock. Whether you have a DuraFlex liner, a HeatShield resurfaced flue, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need a price for your chimney cleaning?Free estimate, price agreed before work starts
Call (855) 473-8720

Signs You Need a Pro Right Now

  • Smoke rolling back into the room. Backdraft means the flue isn’t drafting the way it should, which can come from a blocked flue, a cap issue, or a liner problem. It’s not something to troubleshoot with a fire burning.
  • A ceiling stain or water on the chimney chase. Water showing up near the chimney usually traces back to flashing, a failed crown, or a missing cap. Left alone, it rots framing and masonry from the inside.
  • Crumbling mortar or loose brick. Spalling brick and eroded joints mean the chimney is taking on water. The earlier it’s repointed, the less of the stack has to come down.
  • Cracked or missing flue tiles. Damage inside the flue lets heat and gases reach the chimney structure, which is a genuine safety concern. A trained technician should look at this before the fireplace gets used again.
  • Strong smoky odor even when it’s not burning. Odor in the off season points to creosote buildup or moisture in the flue. A sweep and inspection gets to the cause.

Any of these signs is a reason to have a specialist take a look, whether through chimney sweep service or a standalone inspection. If the issue is structural, we can move straight into repair.

Our Process, Step by Step

  1. 1
    Phone consult and booking. We ask what you’ve noticed, how long it’s been happening, and whether the chimney is wood or gas. That helps us arrive with the right tools and the right expectation. We answer 24/7, and repair calls are booked fast.
  2. 2
    Inspection before any repair. We start with a camera inspection of the flue and a close look at the crown, cap, flashing, and masonry. Nothing gets recommended without camera evidence you can see yourself. If a repair can safely wait, we say so.
  3. 3
    Written estimate. We lay out what’s needed, what isn’t, and the price range for each item. You get a flat price per job agreed before booking, and the written estimate is the final word on cost.
  4. 4
    The repair itself. Whether it’s a HeatShield resurfacing, a DuraFlex liner, flashing rebuilt into the shingles, or masonry repointed with the right mortar, the work is done by chimney specialists. We photograph the completed work and include a photo report.
  5. 5
    Final check and walk-through. We confirm the flue drafts, the cap fits, and the joints are sealed, then walk you through what was done. If you have questions later, the phone line is open.

How Much Does Chimney Repair Cost in Hillsboro?

Chimney repair in Hillsboro typically runs $185 – $1,200 for the common fixes, and $2,400 – $5,200 when a full liner installation is needed. A typical cap install runs $250 – $650, cap replacement $275 – $700, flashing repair $350 – $900, crown repair $450 – $1,200, and masonry repair $500 – $2,800 depending on how much of the stack needs rebuilding. Those are the ranges we see across Hillsboro jobs, and the written estimate fixes the final number.

What moves the price: chimney height and roof pitch, the number of flues, whether a repair is isolated or part of a larger failure, and whether the chimney is masonry or prefab. Access matters too; a steep roof or tight lot adds labor. The biggest single factor is whether you need a liner or whether HeatShield resurfacing can fix the flue, and that’s a camera-call we make on site.

How to avoid overpaying: get a written estimate that itemizes each repair, ask for the camera evidence behind every recommendation, and ask directly whether anything on the list can wait. A specialist will answer all three. Be wary of any company that recommends a full reline without showing you the inside of the flue.

What’s included in a free estimate: the on-site look at the chimney, the camera inspection if needed to scope the repair, and a written flat price per job. No obligation, and the estimate stands. Call (855) 473-8720 to book one.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (855) 473-8720

Our Service Area Near Hillsboro

We serve Hillsboro and the surrounding communities, including chimney repair across Aloha, chimney repair in Cornelius, and work in Forest Grove, Sherwood, Newberg, Wilsonville, Canby, St. Helens, and Portland. Repair calls are booked fast, with dispatch from 7am to 7pm, Sunday through Friday. If you’re outside Hillsboro proper, call and we’ll confirm scheduling for your address.

Serving Hillsboro, OR – Our Local Coverage Area

We serve Hillsboro and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Hillsboro

Schedule Your Chimney Repair Service in Hillsboro Today

If you’ve seen smoke backdraft, a ceiling stain, loose brick, or a cap that’s seen better days, don’t put the fireplace back in service until a specialist has looked at it. We inspect, sweep, and repair in one place, and nothing gets recommended without camera evidence you can see for yourself. Call (855) 473-8720. We answer 24/7, and the estimate is free.

Written by the team at Chimney Sweep Hillsboro.

Why Hillsboro Chooses Chimney Sweep Hillsboro

We set the standard for chimney repair in Hillsboro.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Hillsboro

Getting your chimney repair project started is simple.

1

Call or Request a Free Estimate

Tell us about your chimney repair project and we set up a free visit. No obligation and no hidden fees.

2

Licensed Estimator Visits

A licensed, insured estimator inspects and measures on site, then gives you a clear written price.

3

Scheduled and Done Right

Your crew does the work on the date in your quote, backed by our workmanship warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Hillsboro Customers Say

Trusted by homeowners across Hillsboro and surrounding areas.

★★★★★

"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."

Craig Gallagher
★★★★★

"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."

Michelle Tran
★★★★★

"Cap keeps the birds out now, which after two springs of scratching noises is worth every penny."

Renee Hayes

Ready for Chimney Repair in Hillsboro?

Call now for a free estimate, or request one below. Licensed, insured, and ready to schedule your free estimate in Hillsboro.

(855) 473-8720

Request a Free Estimate in Hillsboro

Tell us about your chimney repair needs. We'll get back to you to set up your free estimate.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Local Service Coverage
Call Now - We Answer 24/7